| 39 1091 01 Rollix Slewing Ring Bearings | Dimension BC:6.38 in; Housing Style:Round Flange; Dimension L Exp:3.32 in; Pre Install Clearance Min:0.040 mm; Dimension R:0.12 in; Full Timken Part Number:QMFY11J055SB; Y1 - Geometry Factor:2.95; Shaft Size :55 mm; Oil Lubrication - B/C/O Seal:1600 rpm; e - Geometry Factor:0.23; Dimension M:2.99 in; Dimension H:0.75 in; UPC Code:0883450032193; Eng Internal Radial Clearance - Max:0.0026; |
| 27 0941 01 Rollix Slewing Ring Bearings | C - Cup Width:1.2500 in; Design Units:Imperial; D:4.7500 in; Series:615; Cup Part Number:612-S; Db - Cup Backface Backing Diameter:4.21 in; Y - ISO Factor3:1.91; e - ISO Factor2:0.31; r - Cup Backface To Clear Radius1:0.030 in; Cg - Geometry Factor:0.0694; Da - Cup Frontface Backing Diameter:4.35 in; |
| 23 1091 01 Rollix Slewing Ring Bearings | Bearing - Housing - Seal:LSE412BRH; Dimension R:14.7 in; Cor - Static Load Rating:111505 lbf; Bolt Size:4 x M24; Cr - Dynamic Load Rating:81606 lbf; Dimension L:7.0 in; Dimension T:17.0 in; Support Type:Round Flange; Note:This product line wa; Maximum Speed:1740 rpm; Dimension V:0.1 in; Dimension N:12.375 in; Ca - Axial Load Rating:4990.69 lbf; Bearing Type:Split Cylindrical Re; Bearing UPC:013992026958; |
| 22 0741 01 Rollix Slewing Ring Bearings | e - Geometry Factor:0.26; Y2 - Geometry Factor:3.90; C0 - Static Load:212000 lb; Dimension D Min:14.46 in; Engineering Group:Mounted Bearing; Int Radial Clearance Reduction Max:0.0035 in; Dimension L:5.35 in; Pre Install Clearance Min:0.0063 in; Int Radial Clearance Reduction Min:0.0025 in; Locking Style:Tapered Adapter; Adapter Sleeve Axial Movement Min:0.035 in; Shaft Size Type:Metric; Grease Lubrication - B/C/O Seal:400 rpm; |
| 75015A Franke Slewing Ring Bearings | A:7.0625 in; E Max.:21.6250 in; D:2.7500 in; B:24.75 in; H:14.5625 in; Assembly Weight:310.000 lb; Bolt Hole Width:1.000 in; Housing Only2:SAF628 x 4-13/16; E Min.:19.3750 in; C:6.750 in; Bolt Hole Length:2.125 in; Triple Seal 2 Req’d:LOR 120; Seal Type:Triple Ring Seal; Diameter S-1:4 13/16 in; F:4.25 in; Bearing Number:22328K; Full Timken Part Number:SAF226284-13/16; E:20.5000 in; Adapter Assembly Number1:SNW-128 x 4-13/16; |
| 121.50.6000.990.41.1502 Standard 5 Slewing Ring Bearings | da - Cone Frontface Backing Diameter:5.31 in; Cone Part Number:EE341048; C1 - Dynamic Radial Rating (1 million revolutions)6:114000 lbf; G1 - Heat Generation Factor (Roller-Raceway):285.8; C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2:51600 lbf; db - Cone Backface Backing Diameter:5.79 in; Cage Type:Pin-Type; R - Cone Backface To Clear Radius3:0.25 in; G2 - Heat Generation Factor (Rib-Roller End):43.6; |
| 36 0411 01 Rollix Slewing Ring Bearings | Bearing Number:23248K; Triple Seal Reqd:ER 914; Adapter Assembly Number1:SNP-148 x 8-15/16; A:10.2500 in; E Max.:30.5000 in; H:20.8750 in; Stabilizing Ring 1 Reqd3:A5679; Diameter S-1:8 15/16 in; Housing Only2:SDAF3248K x 8-15/16; E:29.7500 in; F:8.75 in; Bolt Hole Length:2.375 in; Full Timken Part Number:SDAF23248K8-15/16; C:13.1250 in; Bolt Hole Width:1.625 in; Assembly Weight:1100.000 lb; E Min.:29.0000 in; |
| 33 0641 01 Rollix Slewing Ring Bearings | L:410.00 mm; A1:120 mm; Jmax:356 mm; J:350.00 mm; A2:199 mm; Seal:LO524; Locating Rings (width x OD):SR215X14; Locknut:KM24; Max Grease Speed:2600; Seal Type:Labyrinth; Bearing:22224K; Shaft Diameter d:110 mm; N:26 mm; Housing:SNT 524-620; Jmin:344 mm; H:271 mm; Material :Cast Iron; Housing Mass:26.5 Kg; C0 Static Load Rating:772; Bolt Qty:2; |
| 39 0641 01 Rollix Slewing Ring Bearings | Radial Clearance:0.013 to 0.028 mm; Limiting Speed - Oil:23,000 rpm; Da (max):35 mm; Factor fo:14.8; a (max):1.7 mm; D:37 mm; Configuration:Single Row; Limiting Speed - Grease:19,000 rpm; Dynamic Load Rating:6,350 N; d:20 mm; Groove Diameter:35.7 mm; ra (max):0.3 mm; Static Load Rating:3,700 N; Cy (max):2.3 mm; r1:0.3 mm; Bore Type:Cylindrical Bore; Dx (min):40.5 mm; da (min):22 mm; Fillet Radius/Chamfer:0.3 mm; |
| 37 0841 01 Rollix Slewing Ring Bearings | r1:0.6 mm; D:62 mm; dc (min):40 mm; Radial Clearance:0.020 to 0.045 mm; Bore Type:Cylindrical Bore; Dynamic Load Rating:33,000 N; Inside Ring Outside Diameter:38.5 mm; Da (max):56 mm; B:20 mm; ra (max):1 mm; db (max):37 mm; Configuration:Single Row; Fillet Radius/Chamfer:1 mm; Enclosure:Open; d:30 mm; ra1 (max):0.6 mm; Limiting Speed - Oil:12,000 rpm; Static Load Rating:33,000 N; Limiting Speed - Grease:10,000 rpm; |
| 26 0411 01 Rollix Slewing Ring Bearings | Shaft Size :125 mm; Dimension D Max:17.13 in; Housing Style:Four-Bolt Pillow Blo; Float:0.083 in; C - Dynamic Load (Basic):194000 lb; Eng Internal Radial Clearance - Min:0.0063; C0 - Static Load:237000 lb; Dimension D Min:16.00 in; Dimension G:5.040 in; Grease Lubrication - M/N Seal:650 rpm; Engineering Group:Mounted Bearing; Grease Lubrication - B/C/O Seal:350 rpm; Oil Lubrication - M/N Seal:650 rpm; |
| 6 0675 Rollix Slewing Ring Bearings | Bolt Size:2 x M16; Bearing UPC:013992030115; Seal Type:Felt Type; Weight:28 lb; Maximum Speed:3940 rpm; Shaft Size:60 mm; Support Type:Two-Bolt Plummer Blo; Series Type:Light Series; Bearing Number:LSM60BX; Bearing Type:Split Cylindrical Ex; Dimension M:2.8 in; Cor - Static Load Rating:25853 lbf; Bearing - Housing - Seal:LSM60BXH; Dimension H:3.150 in; Dimension H1:1.3 in; Housing Width:4.0 in; Dimension L:11.0 in; |
| 24 0741 01 Rollix Slewing Ring Bearings | C1 - Dynamic Radial Rating (1 million revolutions)5:14300 lbf; Series:02400; C0 - Static Radial Rating:15800 lbf; d:31.986 mm; K - Factor7:1.4; Cone Part Number:02476X; Da - Cup Frontface Backing Diameter:62.00 mm; da - Cone Frontface Backing Diameter:38.61 mm; db - Cone Backface Backing Diameter:39.62 mm; Design Units:Imperial; e - ISO Factor8:0.42; Bearing Weight:0.30 Kg; a - Effective Center Location3:-5.1 mm; |
| 39 0541 01 Rollix Slewing Ring Bearings | C - Double Cup Width:1.8750 in; G2 - Heat Generation Factor (Rib-Roller End):168; D:8.5000 in; Y1 - ISO Factor5:1.85; Da - Cup Frontface Backing Diameter:8.30 in; e - ISO Factor4:0.36; Cg - Geometry Factor8:0.175; r - Cup Frontface To Clear Radius2:0.03 in; G1 - Heat Generation Factor (Roller-Raceway)7:365; Y2 - ISO Factor6:2.76; Series:L433700; Y - ISO Factor1:1.65; K - Factor3:1.6; Design Units:Imperial; |